Tag: custom

SPX Control

Post author By kmoyer
Post date November 3, 2022

Special Effects Control

The Mission

Enable low-cost DMX control of practical fixtures and effects.

The Execution

I developed and built a custom control module with the assistance of associate designer Christian Curry. The main control module was built with three power supplies at the common voltages that the equipment we used required. Each power supply was fed through a monitor for voltage and current, to provide instant feedback for monitoring and troubleshooting on the output. Each supply fed a terminal block that could then be wired as needed into an 8 channel DMX relay that provided control from the lighting console, that also provided feedback of when a channel was activated. With the relays, it was possible to use both normally open and normally closed switch logic, which allowed us to do effects such as a magnet drop that needed to be powered the whole show.

The Results

Tags custom, dmx, Special Effects

Projects

Blood

Post author By kmoyer
Post date November 3, 2022

Blood

The Mission

Carrie: The Musical is an infamously bloody show, with one of the more notable scenes involving an entire bucket being dumped. The goal was to create a cheap and simple blood solution that could be produced in bulk to use on stage, and enable precise control of the blood.

The Liquid

The props team conducted initial research into potential blood recipies, narrowing down the options to a base of corn syrup mixed with cocoa powder and food coloring. After they conducted small-batch testing to ensure the blood would not stain fabric, we took over and handled scaling to the show quantity. In total, we produced just over 4 gallons of blood for the blood drop, in addition to a smaller batch utalizing glycerin as a corn syrup replacement for a seperate effect.

The Effects

The main blood effect of the show is the blood bucket drop. For the sake of safety and simplicity, the bucket lifted by the actors did not contain any of the blood that got dropped. Instead, the empty bucket was hidden behind a border in the same location as a bucket filled with the dropping blood. This blood was released through a solenoid controlled by the SPX control module, and fed through a wide spray nozzle to give it a more authentic blood look.

The glycerin-based blood was used for an on-person rig. This rig enabled the actor to “bleed out” from their chest. The rig utalized a CO2 cartridge with a regulator, fed into a solenoid for activation. To prevent a misfire, the rig had to first be enabled by a second actor before the first was able to push the button on their chest and fire the rig.

The Results

Tags custom, Special Effects

Projects

The Lordvitator

Post author By kmoyer
Post date November 3, 2022

The Lordvitator

The Mission

Create the illusion of levitation in a large open space without requiring a stagehand, in a way that can be set up and struck within seconds.

The Process

We assembled various components to test the effect with prior to committing to the full rig. This included two types of thread, as well as an Elmo toy as we did not yet own a Jesus statue.

The Execution

The unit, affectionately named the “Lordvitator”, consisted of three DMX controlled stepper motors. These motors have spools attached and wound with fishing line, that then get attached through magnets to the statue.

The software for the rig ran on an Arduino Uno with a MAX485 based shield for DMX input. The unit looked at two DMX channels – one for speed, and one for direction – and updates the movement accordingly. This allowed us to perform the correct movements and speeds with board control.

Not everything goes to plan, and during install one of the connectors snapped off of the DMX board. We made a switch from digital to analog – by simply using a rod mounted behind a wall to move the statue up and down. While this method was more visible, it provided a needed solution to make the effect happen.

The Results

Tags custom, dmx, Special Effects

Portfolio

Carrie: The Musical

Post author By kmoyer
Post date November 3, 2022

Carrie: The Musical

Special Effects Design and Automation

Written by Lawrence D. Cohen // Dir. by Jonathan Strayer // Scenic by Andrue Morgan // Lighting by Adam Boyer // Costumes Victoria Layser // Associate SPX Christian Curry // Photos by University Theatre

The Show

Carrie is a musical adapted from the Stephen King novel of the same name. Notorious for its initial failure and ample use of blood, Carrie follows teenager Carrie White, a teenager girl with telekinetic powers who releases chaos upon her classmates after relentless bullying, culminating in a destrictive prom.

The Mission

The goal with this show was to bring the magic of the director’s vision to life in a manner that matched the intensity of the characters and the emotion of the story, while also balancing the physical limitations of the performance space. I wanted to develop the effects in a practical way, to ensure that they were reliable and cost effective.

The Execution

To realize the vision of the writers and director, I built custom rigs to provide various effects with the assistance of associate designer Christian Curry. Limited stagehands were available, so execution was focused on control through the lighting console. We designed and constructed a main control module to provide multiple power sources switched through DMX controllable relays, alongside a secondary single voltage unit.

We completed a total of 9 effects, most of which were concentrated within a 2 minute “destruction scene” towards the end of the second act. The simplest of these effects, the movement of some chairs through “telekinesis” was achieved through strings pulled by stagehands using cardboard tubes as handles. The most complex single effect was a blood rig for the mother Margret, who has blood seep across her chest. This was achieved through the use of a CO2 cartridge, controlled by a regulator, and triggered by an actor.

Additional Information

The following pages explain some of the effects and controls in greater detail.

The Blood

SPX Control

The Lordvitator

The Results

Tags custom, design, musical, Special Effects, theatre

Portfolio

Her Sister

Post author By kmoyer
Post date March 4, 2022

Her Sister

Lead Electrician

Written by Kendra Phillips // Dir. by Jonathan Strayer // Scenic by Tom Ryan // Lighting by Adam Boyer // Costumes by Priscilla Kaufhold // Sound Design Tony Taylor // Photos by University Theatre

The Show

Her Sister by Kendra Phillips was premiered in 2022 by Millersville University of Pennsylvania as a part of their Conference on The Holocaust and Genocide. The show is a memory play told through the perspective of Margot Frank, traveling through the last few years in her life from her home in Amsterdam.

The Mission

Prepare for and execute lighting design with specialty practicals for a show in a small found-space blackbox theatre.

The Execution

My initial focus was on updating inventories and testing equipment during work calls leading up to the point at which we received the design. This included training technicians to perform testing and small repairs to fixtures, as well as working with one of the manufacturers to verify warranty and receive repair on one of our LED fixtures.

For execution of the plot, I broke the space into three separate bays defined by the rafters of the building. Each bay was given its own universe, and addresses were broken down within. Initially, control was based on running the first moving fixture in each bay on network, with each fixture acting as an output node to the remainder of the bay. The fixtures, however, had a firmware issue that resulted in flickering on the output, so a dedicated control line was run from the console to each bay.

This show featured a mix of real and fake candles. The fake candle had a Multiverse receiver fitted to allow the lighting designer to control the intensity of the flame, with specialty high capacity 9 volt batteries specced to ensure that the candle would last for the duration of the show under the high current draw of the receiver.

The Results

Tags custom, lead, lighting, technician, theatre